WhatsApp Widget


  Next day delivery available - Order before 12pm

  Trusted Supplier & Installer


  Next day delivery available - Order before 12pm

  Trusted Supplier & Installer


  Next day delivery available - Order before 12pm

  Trusted Supplier & Installer



Echosorption PLUS - Reverberation Treatment for Offices, Schools , Gymnasiums & Halls

£349.99 Ex Vat

£419.99 Inc Vat


1200mm x 600mm x 30mm (8)

Total Meterage: 

Product Total-Sub Cost: 

Size Price
1200mm x 600mm x 30mm (8) £419.99


  SRU Insulation Price Promise. Learn more

  Delivery within 3-5 working days

  FREE delivery is available for orders over £500.00 + VAT


ECHOSORPTION - PLUS  stick-on acoustic panels are extremely high performance sound absorption panels. Their lightweight properties and low thickness not only make the panels easy to install but extremely suitable for adhering to a wide range of ceiling and wall surfaces.

These sound absorbing panels are used widely in schools, offices, music studios, lecture theatres, multi purpose halls, interview rooms, training areas and cinemas. They meet the requirements of BB93 of the Building Regulations for acoustics in school buildings and are Class 0 fire rated hence meeting the Fire Regulations as well.

Acoustic Performance

Class A

This fixing method results in very high sound absorption especially at low frequencies which is often very difficult to achieve. This product achieves an absorption coefficient of 1.00 (i.e. 100%) even as low as 160 Hz. This provides a very cost effective bass absorber for studios and music rooms at minimal cost.

The air gap can be created by using 100mm thick timber battens behind the panels or a similar method.

Class C

The special construction of ECHOSORPTION  panels gives a very high sound absorption rating 0.85 (i.e. 85%) with minimum headroom height loss (only 30mm).

The NRC of a standard panel is 0.85 (i.e. 85%) and an emulsion painted surface panel is also 0.85 (i.e. 85%). The only difference is that the thin coating of emulsion paint on the surface acts as a membrane absorber leading to higher absorption at the lower frequencies and a drop off at the higher frequencies. However the overall NRC stays the same at 0.85 (i.e. 85%).

Product Dimensions:

    1200mm x 600mm x 30mm
    8 x Panels per Box

ECHOSORBA acoustic panels are simply adhered to ceilings and upper walls using SRU - High Contact  spray can adhesive.

It is important to check the construction detail of the backing surface structure (ceiling or wall) to which the acoustic panels are to be glued. The ECHOSORBA panels have a thermal conductivity of 0.034 W/mK at 10°C and therefore have good thermal insulation properties as well as excellent sound absorption.

It is therefore important to ensure that there is no possibility of condensation or cold bridging occurring if the acoustic panels are applied to the surface of the structure. Should there be any potential for condensation or cold bridging, then it is very important that this problem is eliminated by suitable treatment, such as a vapour barrier etc, before the ECHOSORBA acoustic panels are installed.

Failure to take suitable precautions may lead to staining of the acoustic panels due to air and moisture movement. This can potentially occur, for example, where there is no heated upper floor above the ceiling to which the acoustic panels are to be fitted. Soundsorba Ltd will not be liable if these precautions are not taken and staining occurs.

SRU High contact adhesive is a quick spray-on application which comes ready to use in 500ml spray cans. The panels and adhesive must be kept and stored inside at room temperature at all times and acclimatised in the area where they are to be used for 24 hours before installation.

The panels are adhered to the backing surface either with a butt joint effect or by using shadow gaps. To avoid soiling the panels, white cotton gloves should be worn when handling them.

The backing surface must be clean, flat, level, dry, solid and free from dust, oil, grease and other similar residue which may affect the adhesion. We recommend that the contact adhesive is applied at room temperature of approximately 21°C and in well ventilated conditions.

Write a review


You may also like...